Differences

This shows you the differences between two versions of the page.

--- wlan:3comofficeconnect [2006/09/23 23:36] – 85.64.51.254
+++ wlan:3comofficeconnect [2007/03/27 14:54] (current) – old revision restored andi
@@ Line 1: / Line 1: @@
+====== 3COM OfficeConnect on Linux======
+{{wlan:3com-front.jpg?250}} {{wlan:3com-back.jpg?200}}
+The exact name is //3com OfficeConnect 11Mbps Wireless LAN CardBus PC Card//. It's an 32Bit cardbus card and the model number is //3CRSHPW796//. A label on the card says its //Version 1//.
+Because this is cardbus card and not a simple PC card it does not show up whith ''cardctl ident'' - instead it is handled by [[:hotplug]] and gets registered as PCI device. ''lspci'' has something to tell:
+:01:00.0 Network controller: 3Com Corporation 3CRSHPW796 [OfficeConnect Wireless CardBus] (rev 15)
+        Subsystem: 3Com Corporation 3CRSHPW796 [OfficeConnect Wireless CardBus]
+        Flags: medium devsel, IRQ 9
+        I/O ports at 4000 [size=256]
+        Memory at 10800000 (32-bit, non-prefetchable) [size=1K]
+        Expansion ROM at 10400000 [size=128K]
+        Capabilities: [c0] Power Management version 2
+===== General Setup =====
+I'll use a vanilla Kernel 2.4.26 from www.kernel.org with PCMCIA and Wireless LAN support. In userspace I use the latest ''pcmcia-cs'' (3.2.5-7), ''[[:hotplug]]'' (0.0.20040329-11) and ''wireless-tools'' (26+27pre22-1) packages from [[:Debian]]s unstable branch. Everything is done on my Fujitsu-Siemens [[:Lifebook]].
+===== ADMtek Driver =====
+There is some info at http://www.espina.info/papers/officeconnect/ stating the card uses an ADMtek chipset. The page describes how to run this card with the half propritary driver provided by ADMtek so I tried that first. You need a patch from this site and the sources from www.admtek.com.tw but I couldn't reach their server :-(. However I found a copy [[http://www.latinsud.com/adm8211/ADM8211_src_105.tar.gz|here]] (or [[http://freecache.org/http://www.latinsud.com/adm8211/ADM8211_src_105.tar.gz|through cache]]). So here is what I did following the instructions on the mentioned page.
+  $> wget http://www.latinsud.com/adm8211/ADM8211_src_105.tar.gz
+  $> wget http://www.espina.info/papers/officeconnect/ADM8211_src_105.patch
+  $> tar -xzvf ADM8211_src_105.tar.gz
+  $> cd ADM8211
+  $> patch -p0 < ../ADM8211_src_105.patch
+  #> ln -s /usr/src/linux /usr/src/linux-2.4
+  $> make
+  #> cp 8211.o /lib/modules/`uname -r`/pcmcia/
+  #> depmod -a
+The ''depmod'' returns an ''unresolved symbols'' error but adding the following to ''/etc/pcmcia/local.conf'' gave me a new ''eth1'' device:
+<file>
+device "8211"
+   class "network" module "8211"
+card "3Com Corporation"
+  manfid 0x10b7,0x6000
+  bind "8211"
+</file>
+Even the ''dmesg'' output looked fine:
+<code>
+cs: cb_alloc(bus 1): vendor 0x10b7, device 0x6000
+PCI: Enabling device 01:00.0 (0000 -> 0003)
+ADM8211 Linux driver version 1.05 (June 24, 2003)
+PCI: Setting latency timer of device 01:00.0 to 64
+: Hardware Address 00:0B:AC:E6:9C:D8, IRQ 9.
+eth1: ADMtek Wireless rev 21 at 0x4000
+</code>
+Everything looked good but setting the ESSID with ''iwconfig eth1 essid "foo"'' failed. There is no error message but the ESSID gets not set. Some googling brought up [[http://www.linuxquestions.org/questions/showthread.php?postid=1000617#post1000617|this post]] saying the driver does not work with newer Kernels. Doh! :-/
+===== GPL Driver =====
+Luckily there is a GPL'd driver available at http://aluminum.sourmilk.net/adm8211/ - it is very new and should be considered as beta. It is developed for the 2.6.x series Kernel but the INSTALL file says it works with 2.4.x, too. So lets try:
+  $> wget adm8211-20040711.tar.bz2
+  $> tar -xjvf adm8211-20040711.tar.bz2
+  $> cd adm8211
+  $> make
+  #> make install
+Be sure to delete the ''8211.o'' module if you tried the factory driver before. Then insert the card and run ''dmesg'' to check what happens:
+  cs: cb_alloc(bus 1): vendor 0x10b7, device 0x6000
+  PCI: Enabling device 01:00.0 (0000 -> 0003)
+  adm8211: Copyright 2003, Jouni Malinen <jkmaline@cc.hut.fi>; Copyright 2004, Michael Wu <flamingice@sourmilk.net>
+  adm8211: release 20040711
+  PCI: Setting latency timer of device 01:00.0 to 64
+  eth1: EEPROM type: 93C66
+  eth1: RFtype=1 BBPtype=1 Specific BBP=0 Transceiver=0
+  eth1: Channel range: 1-11
+  eth1: hwaddr 00:0b:ac:e6:9c:d8, IRQ 9, Rev 0x15, PCI ID: 0x82011317, mem @0x10800000 (len=0x400)
+Looks nice :-) Lets get it up:
+  #> iwconfig eth1 essid "MeinKleinesWLAN" key restricted 's:13chars ASCII' mode Managed
+  #> dhclient eth1
+Did it work? Well for me it did :-D. 1:0 for open source :-)
+=====3com Driver=====
+I just discovered that 3com it self provides a linux for the card at their [[http://www.3com.com/products/en_US/result.jsp?selected=all&sort=effdt&order=desc&sku=3CRSHPW796|support page]]. It looks a lot like the ADMtek driver but unlike the above mentioned driver it works ;-)
+The setup is easy. Get the driver from the support site, unpack compile and install:
+  $> tar -xzvf 3CRSHPW796.tar.gz
+  $> cd source
+  $> make
+  #> cp adm8201.o /lib/modules/`uname -r`/kernel/drivers/net/wireless/
+  #> modprobe -a
+Running ''depmod'' prints an //Unresolved Symbols// error, but inserting the card loads the driver:
+<code>
+cs: cb_alloc(bus 1): vendor 0x10b7, device 0x6000
+PCI: Enabling device 01:00.0 (0000 -> 0003)
+PCI: Setting latency timer of device 01:00.0 to 64
+eth1: EEPROM type: 93C66
+eth1: RFtype=1 BBPtype=1 Specific BBP=0 Transceiver=0
+eth1: Channel range: 1-11
+eth1: hwaddr 00:0b:ac:e6:9c:d8, IRQ 9, Rev 0x15, PCI ID: 0x82011317, mem @0x10800000 (len=0x400)
+</code>
+Again setting your WLAN parameters and getting an IP via DHCP is just two commands away:
+  #> iwconfig eth1 essid "MeinKleinesWLAN" key restricted 's:13chars ASCII' mode Managed
+  #> dhclient eth1
+Nice. Now you have two different drivers to choose from for this card.